B&D Controll-A-Door ShedMaster Spécifications télécharger pdf (Page 12)

SETTING SAFETY OBSTRUCTION FORCE

8. SAFETY OBSTRUCTION TEST

Please take care when testing the Safety Obstruction Force.

Due to Excessive forces failure to follow this warning may

cause SERIOUS PERSONAL INJURY and/or property

damage. The test below should be repeated at regular

intervals (approximately every two months).

8.1 TESTING CLOSE CYCLE

Open the door by pressing the OPERATE button (Fig. 11).

2. Place a length of timber approximately 50mm high on the

floor directly under the door (Fig. 12).

3. Press the OPERATE button to close door. The door should

strike the object and start to re-open.

NOTE: If the door stops and fails to reopen, it is possible that

the motor direction is set incorrectly. Change the motor

direction and retest.

IMPORTANT WARNING: If the test fails, there may be a

problem with the door, discontinue use, put the door into

manual operation and call for service.

8.2 TESTING OPEN CYCLE

1. With the door closed - press the OPERATE button to open

the door. When the door is approximately one metre above

the timber hold the bottom rail of the door firmly, the door

should stop.

ADJUSTING SAFETY OBSTRUCTION FORCE

The Safety Obstruction Force is calculated automatically and

set in memory on the Shed Master. It is usually not necessary to

adjust the Safety Obstruction Force. The only time the force

may need to be increased is due to environmental conditions,

for example, windy or dusty areas, and areas with extreme

temperature changes. If adjustments are made you must retest

the obstruction force margin as per above.

8.3 TO INCREASE FORCE PRESSURE

1. Press and hold the Force Margin Set button (Fig. 11)

2. While holding down the Force Margin button, press the

Plus button. Each press increases the force margin in both

directions. The Open Limit LED will illuminate each time

the Plus button is pressed. Each press increases the force

margin. Test the force as per step 8.1 and 8.2. If the Open

Limit LED flashes continuously when the Plus button is

being pressed, this indicates that the maximum force

pressure setting has being reached.

8.4 TO DECREASE FORCE PRESSURE

1. Press and hold the Force Margin Set button (Fig. 11).

2. While holding down the Force Margin button, press the

Minus button. Each press decreases the force margin. The

Close Limit LED will illuminate each time the Minus button

is pressed. Test the force as per step 8.1 and 8.2. If the Close

Limit LED flashes continuously when the Minus button is

being pressed, this indicates that the minimum force

pressure setting has been reached.

FIG. 12

8.5 TO RECALL FACTORY SET FORCE

1. While holding down the Force Margin Set button (Fig. 11)

press the SET button for two (2) seconds.

2. Release both buttons. The default setting should now be

recalled.

8.6. TO RE-CALCULATE FORCE MARGIN

Press and hold the Set Button for two (2) seconds, the beeper will

sound once. The door will start to move and re-calculate force

margins. The door can move between the open and close limit

positions up to four (4) times (depending on the position of the

door and the power up condition). A single beep will be heard once

the process is complete. The door is now ready for use.

IMPORTANT NOTE:

After installation ensure that the opener stops or is

prevented from opening when the door is loaded

with a mass of 20kg fixed centrally at the bottom

edge of the door.

FIG. 11

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

B&D Controll-A-Door ShedMaster Spécifications Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Ouvreur de porte de garage B&D Controll-A-Door ShedMaster